Bosch Solution 16 Sector Alarm Panel
Bosch LCD keypad
Bosch 3 Quad Passive Infrared PIR
Blue Strobe light
12V 7AHr SLA rechargeable battery
Plug pack power supply
Eight programmable user codes and eight radio remote user codes
Up to sixteenuser codes (User Codes 1-16) and an additional eight radio user codes (User Codes 9-16) may be
programmed to operate the system. For security, only the Master Code holder can add or change other system
user codes including the Master Code itself.
The Solution 16 control panel can be partitioned or split into two individual areas. Both areas can be
operated from one Master Partitioned codepad or from separate area addressable codepads.
The system can be armed in any of three modes:
AWAY Mode: Arms the entire system.
STAY Mode 1: Arms all zones except those programmed by the installer to be automatically isolated.
STAY Mode 2: Arms all zones except those programmed by the Master Code holder to be automatically isolated.
Remote arm facility allows the system to be armed from any remote location via the telephone. For obvious
security reasons, the system cannot be disarmed using this method. A touch-tone telephone is required to
use this feature. For this feature to operate, it must be programmed at installation.
Day alarm allows a combination of zones to be monitored during the disarmed state by beeping the codepad
buzzer. An example of a day alarm would be the front door of a shop that has a pressure mat or electronic
beam that customers activate as they enter to and from the shop. As the customers walk onto the pressure
mat or break the electronic beam, the codepad buzzer will beep. Zones 1-4 can be programmed at installation
to operate for day alarm.
Duress alarm is used as a silent hold up alarm. A duress alarm is only useful if the system is programmed to
report to a monitoring station or pocket pager as domestic reporting (i.e. mobile phone, etc) can't decipher
which type of alarm has occurred.
Code Pad Tamper alarm restricts the number of times an invalid user code can be used in an attempt to operate
the system. When the number of incorrect code attempts equals the number programmed at installation, the
stem will activate an alarm condition and if reporting back to a security monitoring station, the system will
send an access denied report.
Choice of End-Of-Line (EOL) resistor value
The control panel has the ability to be programmed for different values of EOL resistors. This is a global
parameter and affects all four zones simultaneously. It gives the ability to fit the Solution 880 Control
Panel into an existing installation without having to change the EOL resistors. This feature also increases
the security of the system as there are eleven possible EOL resistor values that can be used. This makes for
convenient panel swap-out to add to the flexibility of the Solution range of products.
Built-in telephone line fail monitor
A telephone line fault will register when the system detects that the telephone line has been disconnected
from the control panel. The system can be programmed to sound if the telephone line is cut whilst the panel
Dynamic battery testing
The system automatically performs a battery test every 4 hours and also every time you arm the system. A low
battery fault will register when the system detects a low capacity back-up battery.
AC Fail and System Fault Indicators
If a fault occurs, the FAULT or MAINS indicator will flash and the codepad will beep once ever minute.
Event memory recall
This function allows replay of the last forty events that occurred to the system. The event memory history
will replay all alarms and arming/disarming of the system in AWAY Mode, STAY Mode 1 and STAY Mode 2.
However,the system cannot differentiate between arming the system in STAY Mode 1 or STAY Mode 2.
Telco arm/disarm sequence (Call Forwarding)
This feature is only available if the call-forward option is available from the telecommunications provider.
It allows programming of the Call Forward -Immediate On sequence or Call Forward -No Answer sequence that
will automatically operate when the system is armed in the AWAY Mode.
Upload/download programmable-Note: the examples given below are only applicable to Australia.
Call Forward -Immediate On: This feature redirects all incoming calls to another number anywhere in
Australia, including mobiles, pagers and answering services. When Call Forward -Immediate On is turned on,
the telephone that was originally called will not ring.
Call Forward -No Answer: This feature redirects all incoming calls to another number anywhere in Australia
when the telephone that was originally called is not answered within 20 seconds. Outgoing calls can still be
made from the original telephone.